产品描述：

HENRY 135 玻化砖石材粘合剂是优选天然矿物原料和改性聚合物配制而成的粘合剂。该产品相对于传统的水泥砂浆更具有粘结力、施工便捷、薄贴工艺节省空间、减少材料损耗，其超强的粘结力使低吸水率的瓷砖铺贴更持久牢固。

 

产品特点：

● 优异的抗滑移性能;

● 施工性好、耐候性好;

● 粘结力好、防止砖脱落。

 

用法用量：

1、将产品倒入清水中搅拌成膏状，注意要先加水后再倒入产品，搅拌时使用电动搅拌机；

2、混合比：25kg产品：5.0-5.5L清水

3、充分搅拌均匀至无粉团，搅拌完成后需静置五分钟，再稍作搅拌后使用，更有利于增加粘结力。

4、用齿形刮刀胶膏状瓷砖胶均匀涂布于基层表面，并形成均匀条齿状。单次涂布面积建议不超过1m²（可视天气温度适当调整），然后在晾置时间内铺贴瓷砖即可。

5、齿形刮刀的选择应根据工作面的平整度和瓷砖背面的凹凸程度而定。

6、如瓷砖背面凹凸程度较大，则应进行双面涂胶，即在工作面和瓷砖背面同时涂上瓷砖胶。

7、用量：1.5kg/m²/mm。

 

注意事项：

1、该产品按参考比例加水即可使用，禁止添加其它材料。

2、施工温度为5-35℃；

3、水粉比例可因基层、天气、施工条件等不同而做出适当调整；

4、搅拌好的粘合剂应在2小时内使用完毕，杜绝将已干结的粘合剂拌水使用；

5、铺贴施工完成后，需待粘合剂完全干固后，24小时后才可以进行下一步的填缝工作；

6、铺贴瓷砖时，砖与砖之间必须留有≥2㎜的缝隙；

7、在进行墙面铺贴时，注意做好临时固定措施。

8、室内施工高度应≤4m。

 

执行标准：JC/T 547-2017 C1T

 

储存运输： 本品须存放于干燥、通风的室内环境，防潮、防水、防止暴晒，保质期为12个月。

 

包装： 20KG、25KG/包

 

 

 

HENRY 135 Porcelain and Stone Adhesive

 

Discription:

The Porcelain and Stone Adhesive is made of natural mineral materials and modified polymer. Comparing with traditional cement mortar, this product has advantages of good adhesion, easy to use, environmental-friendly and safety. The thin paste method can save space and materials; the super adhesion make sure the tiles with low water absorption can be applied with more durability and firmness.

 

Features:

Excellent slip resistance; Good adhesion;

Prevent the tiles from falling off;

Easy to use and good weather resistance.

 

Application:

1. The powder should be added into clean water in a clean container whilst stirring vigorously and mixed thoroughly to give easily worked mortar.

2. Mixing ratio: powder: water =25Kg: 5-5.5L;

3. Allow to stand for 3 minutes during the mixing, then restir the mortar thoroughly. This procedure can increase the bonding strength of the mortar.

4. Apply the mortar evenly on the surface of the substrate with a notched trowel and make sure to press the tiles into the freshly combed mortar in open time.

5. The type of notched trowel is depending on the substrate conditions and size of tiles.

6.To increase the bonding strength, both of the substrate and back of the tiles should be applied with mortar.

7. Coverage: 1.5kg/mm/m².

 

Notes:

1. Please following the mixing ratio, other materials should not be added during the mixing.

2. The application temperature is 5-35 ℃;

3. The water/powder ratio will vary depending on the substrate, weather and site condition;

4. The mortar should be applied within approx.2 hours. Do not reuse the dry mortar by adding water again;

5. Grouting may be allowed approximately 24 hours after the application;

6. Seamless application is forbidden, the width of tile joints should be ≧ 2mm 

7. Pay attention to provisional fixing measures during the wall application

8. Interior application height should be ≤ 4 m.

 

Technical Data：

JC/T 547-2017 C1T

 

Storage& Shelf Life:

This product has a shelf life of approximately 12 months if stored in a dry, cool, ventilated place in original unopened packaging

 

Package:20kg、25kg/bag

 

Notes:

If in doubt, create small area trial before large area application. we are not responsible for the loss caused by ignoring the problems occurred in trial. if you have any questions about application, please consult our technical support team.