特点：

● 适用多种类主材、基材粘合

● 极高的终粘强度确保主材尺寸稳定性

● 可用于结构粘合加固、可承受高荷载

● 固化后耐水，室内外均可使用

 

用途：

● 适用于PVC地板、亚麻地板、橡胶地板、木地板、钢板、人造草皮及瓷砖等材料的铺贴，适合用于各种类型的基层上，如：水泥砂浆、混凝土、木板、瓷砖、石材、金属等基层。尤其适用于在高荷载基层上。

刮齿类型                      用 量

● A2或A3                    300-500g/m²

● B1或B2                     400-600g/m²

 

基层说明：

● 基层必须平整、坚固、干燥、清洁，没有裂缝以及影响粘结性能的物质。如果基层表面不平整，请用亨历自流平进行找平。

混合比: 施工温度: 工作时间: 可通行时间: 终粘强度:

A组份：  B组份 100  ：  15（重量比） 介于5-30℃之间 0-50分钟 24小时 48小时

Mixing ratio: Working temperature: Working time: Walkability: Full cure:

A : B=100：15   between5-30℃ 0-50 minutes 24 hours 48 hours

※数据在23±2℃时的正常条件下适用。

 

施工说明：

● 使用前，请打开大桶，然后将小桶中的固化剂彻底倒入大桶（注意小桶内是否完全倒尽）并用合适的电动搅拌器充分搅拌。确保搅拌彻底、均匀，色泽一致。多人施工，以防止过快固化（气温高于25℃尤其需要注意）。搅拌时尤其注意容器壁和底部。用刮板将本品均匀涂布在基层表面。铺设地板并均匀滚压。2-3小时再次对地板滚压。确保胶水充分转移至地板背面。施工后可用醋酸乙酯来清洗工具。

 

注意事项：

● 置于原包装内在凉爽、干燥的条件下。在低温的条件下产品会变稠。

● 最佳施工条件：气温23±2℃，相对空气湿度40%-75%。施工材料和地面温度不得低于0℃。低温可使固化时间延长，高温可缩短产品的工作时间。

● 搅拌后的产品在容器中会很快固化，需尽快施工。

● 施工时请穿戴好防护手套、眼镜等。

● 避免B组份与皮肤和眼睛接触。接触到皮肤时，用大量清水和肥皂清洗。接触到眼睛时，立即用流动的清水冲洗15分钟然后就医检查。不可将本产品废料倒入下水道中。

 

包装与储存：

● A组份：10kg     B组份：1.5kg

本品须存放于5℃~35℃环境中，保质期为12个月。

 

 

 

Features：

Suitable for various floor covering and substrate;

High bonding strength to ensure the dimensional stability of floor covering;

Can be used for structural bonding and reinforcement, high load bearing;

Water resistant;

For indoor and outdoor use;

 

Uses:

Suitable for PVC floor, linoleum floor, rubber floor, wood floor, plate, artificial turf and ceramic tile materials of paving, suitable for various types of grass, such as: cement mortar, concrete, wood, ceramic tile, stone, metal, etc. base, especially for areas subject to high loads.

Substrate Preparation:

The substrate must be mature, sound, solid, clean and dry with good surface integrity. Any repairs, levelling or smoothing should be carried out using HENRY relevant products.

 

Types of toothed scrapers A2 or A3 B1 or B2

Consumption 300-500g/m2 400-600g/m2

 

Mixing and Application:

The entire contents of Part B container should be poured into Part A container, then thorough mixing with an electric drill fitted to create one homogeneous mix and an even color is obtained. Work to an area that suits the size of the installing team. The adhesive should be applied evenly over the substrate using the appropriate serrated trowel. Ensure that there is correct transfer of the adhesive to the back of the floorcovering .After 2-3 hours press down or roll floorcoverings again. Clean tools immediately after use with acetone or spirits.

 

Notes：

1. The original package should be stored in cool, dry conditions. Lower temperature may decrease the fluidity.

2.Recommended working condition：23±2℃,40%-75%RH. Do not apply at temperatures below 0°C.Working time will be extended at lower temperatures, and this time will be shorted as higher temperature.

3. Apply the products immediately after mixing.

4. During mixing and application, always wear protective gloves and glasses as necessary. In case of contact with the eyes, rinse immediately with plenty of water for 15 minutes and seek medical advice and after contact with the skin wash immediately with plenty soap and water (do not use solvents).

 

Package and Storage：

Part A：10kg              Part B：1.5kg

HENRY 450 has a shelf life of 12 months if kept in a dry store between 5℃ to 35℃.